I bought a new HP x360. As expected it comes with a slow drive loaded to the gills with bloatware. So I planned from the beginning to install a fresh copy of 8.1 on a SSD.
I used a new SSD and without doing too much reading created a bootable usb from the 8.1 upgrade with key link. Unbeknownst to me is that the win 7 machine I used (where I previously created a usb key for win 8 pro) is also a pro install that retained the previous key. It never asked for a key when creating the usb. So I ended up with a pro install on the HP laptop and I could not enable the key associated with the laptop.
Thus I started over. I tried various things to create a non-pro usb and had a lot of problems and tried various things. I ultimately succeeded in creating a x64 core 8.1 usb. Now my challenge is that I cannot see the SSD anymore. Even in diskpart I cannot see the ssd. At some point while the ssd was still available (but my install usb did not work due to wrong key) I ran diskpart with the following:
clean
create partition primary
select partition 1
active
format fs=ntfs
assign
Since then I could not see the ssd
I have tried the following:
Put original disk back in. Install Paragon. Clone install over to ssd. Put ssd back in laptop. "No bootable device found"
Put ssd in win 7. Run diskpart. Clean All. Convert GPT.
It is possible the problem lies in the bois. The model laptop is brand new. I updated the bios (it was 2 versions old). But HP site had no explanation of what changed in bios.
I also enabled legacy support.
BTW the only way I can create a bootable usb is with Zotac WinUSB maker. Even with win7 usb maker the drive is not recognized. With Zotac I can enable EFI. If I create the image without EFI the laptop does not see it (again even if legacy support is enabled).
So to summarize;
With official 8.1 upgrade image and fresh SSD I could install
After that with 8.1 iso and drive cleaned with diskpart I cannot see drive
Any help? Please!!
EDIT: I tried again with the upgrade win 8.1 with product key and it worked again. Then I again tried with the ISO. I used a guide on this forum for Rufus and using 7-zip. But it still will not recognize the ssd. I get "a media driver your computer needs is missing". A common problem for this is using usb3. I tried with usb 3 and 2. When I shift=f10 and list disk I do not see the ssd.
I used a new SSD and without doing too much reading created a bootable usb from the 8.1 upgrade with key link. Unbeknownst to me is that the win 7 machine I used (where I previously created a usb key for win 8 pro) is also a pro install that retained the previous key. It never asked for a key when creating the usb. So I ended up with a pro install on the HP laptop and I could not enable the key associated with the laptop.
Thus I started over. I tried various things to create a non-pro usb and had a lot of problems and tried various things. I ultimately succeeded in creating a x64 core 8.1 usb. Now my challenge is that I cannot see the SSD anymore. Even in diskpart I cannot see the ssd. At some point while the ssd was still available (but my install usb did not work due to wrong key) I ran diskpart with the following:
clean
create partition primary
select partition 1
active
format fs=ntfs
assign
Since then I could not see the ssd
I have tried the following:
Put original disk back in. Install Paragon. Clone install over to ssd. Put ssd back in laptop. "No bootable device found"
Put ssd in win 7. Run diskpart. Clean All. Convert GPT.
It is possible the problem lies in the bois. The model laptop is brand new. I updated the bios (it was 2 versions old). But HP site had no explanation of what changed in bios.
I also enabled legacy support.
BTW the only way I can create a bootable usb is with Zotac WinUSB maker. Even with win7 usb maker the drive is not recognized. With Zotac I can enable EFI. If I create the image without EFI the laptop does not see it (again even if legacy support is enabled).
So to summarize;
With official 8.1 upgrade image and fresh SSD I could install
After that with 8.1 iso and drive cleaned with diskpart I cannot see drive
Any help? Please!!
EDIT: I tried again with the upgrade win 8.1 with product key and it worked again. Then I again tried with the ISO. I used a guide on this forum for Rufus and using 7-zip. But it still will not recognize the ssd. I get "a media driver your computer needs is missing". A common problem for this is using usb3. I tried with usb 3 and 2. When I shift=f10 and list disk I do not see the ssd.
Last edited:
My Computer
System One
-
- OS
- 8.1/7