Windows 8 and 8.1 Forums

Error message when using recimg to create custom image

  1. #1

    Posts : 1
    Windows 8.1

    Error message when using recimg to create custom image


    Am using recimg to create custom image on freshly upgraded win 8.1 install. It fails almost immediately with this message appearing in a pop up:

    "The procedure entry point ??0BufferedStream@UnBCL@@QEAA@PEAVStream@1@K@Z could not be located in the dynamic link library c:\windows\system32\migwiz\migcore.dll"

    Any tips would be great .. thanks

    Further info:

    Problem signature:
    Problem Event Name: APPCRASH
    Application Name: recimg.exe
    Application Version: 6.3.9600.16412
    Application Timestamp: 5243fc60
    Fault Module Name: KERNELBASE.dll
    Fault Module Version: 6.3.9600.16408
    Fault Module Timestamp: 523d557d
    Exception Code: c06d007e
    Exception Offset: 000000000000ab78
    OS Version: 6.3.9600.
    Locale ID: 1033
    Additional Information 1: 789a
    Additional Information 2: 789afc645168a35af715ce92aecac0c2
    Additional Information 3: 633e
    Additional Information 4: 633e2518fd5dbdf6a3b0d6875de26d5c

    system info :
    OS Name Microsoft Windows 8.1
    Version 6.3.9600 Build 9600
    Other OS Description Not Available
    OS Manufacturer Microsoft Corporation
    System Name TOSHIBA
    System Manufacturer TOSHIBA
    System Model Satellite C55-A
    System Type x64-based PC
    System SKU PSCF6U
    Processor Intel(R) Pentium(R) CPU 2020M @ 2.40GHz, 2400 Mhz, 2 Core(s), 2 Logical Processor(s)
    BIOS Version/Date Insyde Corp. 1.20, 6/7/2013
    SMBIOS Version 2.7
    Embedded Controller Version 1.30
    BIOS Mode UEFI
    BaseBoard Manufacturer TOSHIBA
    BaseBoard Model Not Available
    BaseBoard Name Base Board
    Platform Role Mobile
    Secure Boot State On
    PCR7 Configuration Binding Not Possible
    Windows Directory C:\WINDOWS
    System Directory C:\WINDOWS\system32
    Boot Device \Device\HarddiskVolume2
    Locale United States
    Hardware Abstraction Layer Version = "6.3.9600.16408"
    User Name TOSHIBA\Jeff
    Time Zone Central Standard Time
    Installed Physical Memory (RAM) 6.00 GB
    Total Physical Memory 5.88 GB
    Available Physical Memory 2.59 GB
    Total Virtual Memory 7.51 GB
    Available Virtual Memory 3.65 GB
    Page File Space 1.63 GB
    Page File C:\pagefile.sys
    Hyper-V - VM Monitor Mode Extensions Yes
    Hyper-V - Second Level Address Translation Extensions Yes
    Hyper-V - Virtualization Enabled in Firmware Yes
    Hyper-V - Data Execution Protection Yes

      My System SpecsSystem Spec

  2. #2

    Posts : 1,121
    Windows 8.1 x64

    If you have posted this problem in several forums, I do not have an answer. If this is your only post, it appears Toshiba is having a situation and needs to work it out.

    Have you contacted Toshiba or their forum, if they have one?
      My System SpecsSystem Spec

  3. #3

    Posts : 1,875
    Windows 10 Pro Prieview x64

    What have you done to try to fix this?

    Try SFC /SCANNOW Command - Run in Windows 8
    Try DISM - Fixing Component Store Corruption in Windows 8

    Run them both a few times as admin as the tutorials suggest. If these do not work and you still have an issue with a core Windows dll you should run the upgrade again.

    You don't want a backup of a non-working system - you would be wasting your time.
      My System SpecsSystem Spec

Error message when using recimg to create custom image

Similar Threads
Thread Forum
Refresh Windows 8 - Create and Use Custom Recovery Image
How to Create a Custom Recovery Image to Use to Refresh Windows 8 and 8.1 This tutorial will show you how to create and register a custom recovery image to use instead of default when you refresh your Windows 8, Windows RT, Windows 8.1, and Windows 8.1 RT PC. You must be logged in as an...
Custom Refresh (recimg) fails to run-error pic attached
I was checking my uncle's laptop (He's clueless.) (2013 Toshiba Satellite Intel i3, 6gb, 750gb HD, Windows 8.1) on Thanksgiving. I was doing basic maintenance. I ran Windows Defender, SFC, CHKDSK. I created restore points and updated some software. All OK. I went to run the Custom Refresh...
Performance & Maintenance
Can't create system image. 0x80780119 error after upgrade
Hello! I have upgraded my Windows 8 PC to 8.1 yesterday and it seemed like everything is working fine until I tried to create System Image. I got an error 0x80780119 saying that there is to little space on one of the partitions. I started looking into this problem and indeed one of the...
Performance & Maintenance
Use recimg to create a snapshot of your system, including
I was doing some Google searches looking at information on Windows 8 backup possibilities, and came across this: Create a Windows 8 image with recimg.exe to preserve your Desktop apps after a refresh - Matt Harrington - Site Home - MSDN Blogs I'm running it now to see what it does. Looks very...
Performance & Maintenance
recimg error 0x8007007b
I tried to create a custom refresh image using recimg and got an error code 8007007b. I cannot find any information on this error. Perhaps someone knows what it might mean. The administrator command prompt windows reads as follows: C:\WINDOWS\system32>recimg /createimage...
General Support
Recimg error 80070002
I was trying out the recimg function today for the first time and encountered the 8007002 error. I tried both the manual method and RecImgManager from Slimware. Both failed. All posted remedies on Microsoft were inapplicable, as were the few other listings on other sites. What I discovered was...
Performance & Maintenance
Error while trying to create a system image
This is my first time posting here so please forgive any omissions. I just purchased a new laptop with windows 8 preinstalled. It has no data on it and I've only installed MS Office 2007 and Outlook 2010. Apart from that, everything is brand spanking new. I wanted to create a system image so...
Performance & Maintenance

Eight Forums Android App Eight Forums IOS App Follow us on Facebook